ADAS Static Calibration Laser Measuring Floor Markers - Full Set - 11pcs
Use these Floor Marking Squares to do LDWS, BSM, ACC, Multi View Camera, Eyesight, Laser/Radar and any other Static Calibration.
Made out of 100% Solid Rubber
SGADAS-STD are 1/4" Thick (6.35mm) Measure 2 3/4" x 2 3/4" (70mm x 70mm)
SGADAS-30 & SGADAS-39 are 1/4" Thick (6.35mm) Measure 2 3/4" x 3 7/8"" (70mm x 97mm)
Use these instead of tape or chalk to mark the required positions on the floor when setting up your ADAS Static Calibrations.
Full Set of 11 ADAS Laser Floor Markers (11Pcs Total)
SGADAS-STD - 8 Floor Markers
SGADAS-30 - 2 Floor Markers
SGADAS-39 - 1 Floor Marker
See How to use/layout examples for each type in the pictures
Can be used with ANY ADAS Calibration System that requires markings on the floor for proper target stand placement.
Reusable
Lightweight - Yet heavy enough to stay in place on the floor (even when it's damp or wet)
Coated in visible white reflective paint for easy to see laser markings
Easy to find center line as each piece is V cut both ways
Center of Marker is marked clearly (See Plumb Bob Pictures & 5 Line Laser Pics)
Easy to make measurements with tape measure by lining up end of tape measure or distance needed with bottom of V cut
45 Degree Angle on all 4 sides for visibility of laser line when adjusting centerline (Especially when adjusting centerline under the vehicle.)
Can be used with Reflective Board
Made in USA
SGADAS- STD - These are standard marking squares that you will use with most vehicles you calibrate.
SGADAS-30 - Unique to Subaru Calibrations when using the Target Board that requires a 30mm Offset (Example - Autel Target Board - CSC0601/14)
SGADAS-39 - Unique to Hyundai & KIA Calibrations - Place in front of vehicle with plumb bob and have your 39mm from front target stand measurement automatically set.
ADVANTAGES of using these:
No more dirty floor issues that the tape won’t stick too
No more chalk lines to mark and remove
No more having to buy tape
best of all we have to say these markers have saved us a lot of setup time per job!
They literally pay for themselves in very little time and are an inexpensive investment at $129.99 for these 11pcs.
Use these Floor Marking Squares to do LDWS, BSM, ACC, Multi View Camera, Eyesight, Laser/Radar and any other Static Calibration.
Made out of 100% Solid Rubber
SGADAS-STD are 1/4" Thick (6.35mm) Measure 2 3/4" x 2 3/4" (70mm x 70mm)
SGADAS-30 & SGADAS-39 are 1/4" Thick (6.35mm) Measure 2 3/4" x 3 7/8"" (70mm x 97mm)
Use these instead of tape or chalk to mark the required positions on the floor when setting up your ADAS Static Calibrations.
Full Set of 11 ADAS Laser Floor Markers (11Pcs Total)
SGADAS-STD - 8 Floor Markers
SGADAS-30 - 2 Floor Markers
SGADAS-39 - 1 Floor Marker
See How to use/layout examples for each type in the pictures
Can be used with ANY ADAS Calibration System that requires markings on the floor for proper target stand placement.
Reusable
Lightweight - Yet heavy enough to stay in place on the floor (even when it's damp or wet)
Coated in visible white reflective paint for easy to see laser markings
Easy to find center line as each piece is V cut both ways
Center of Marker is marked clearly (See Plumb Bob Pictures & 5 Line Laser Pics)
Easy to make measurements with tape measure by lining up end of tape measure or distance needed with bottom of V cut
45 Degree Angle on all 4 sides for visibility of laser line when adjusting centerline (Especially when adjusting centerline under the vehicle.)
Can be used with Reflective Board
Made in USA
SGADAS- STD - These are standard marking squares that you will use with most vehicles you calibrate.
SGADAS-30 - Unique to Subaru Calibrations when using the Target Board that requires a 30mm Offset (Example - Autel Target Board - CSC0601/14)
SGADAS-39 - Unique to Hyundai & KIA Calibrations - Place in front of vehicle with plumb bob and have your 39mm from front target stand measurement automatically set.
ADVANTAGES of using these:
No more dirty floor issues that the tape won’t stick too
No more chalk lines to mark and remove
No more having to buy tape
best of all we have to say these markers have saved us a lot of setup time per job!
They literally pay for themselves in very little time and are an inexpensive investment at $129.99 for these 11pcs.
Use these Floor Marking Squares to do LDWS, BSM, ACC, Multi View Camera, Eyesight, Laser/Radar and any other Static Calibration.
Made out of 100% Solid Rubber
SGADAS-STD are 1/4" Thick (6.35mm) Measure 2 3/4" x 2 3/4" (70mm x 70mm)
SGADAS-30 & SGADAS-39 are 1/4" Thick (6.35mm) Measure 2 3/4" x 3 7/8"" (70mm x 97mm)
Use these instead of tape or chalk to mark the required positions on the floor when setting up your ADAS Static Calibrations.
Full Set of 11 ADAS Laser Floor Markers (11Pcs Total)
SGADAS-STD - 8 Floor Markers
SGADAS-30 - 2 Floor Markers
SGADAS-39 - 1 Floor Marker
See How to use/layout examples for each type in the pictures
Can be used with ANY ADAS Calibration System that requires markings on the floor for proper target stand placement.
Reusable
Lightweight - Yet heavy enough to stay in place on the floor (even when it's damp or wet)
Coated in visible white reflective paint for easy to see laser markings
Easy to find center line as each piece is V cut both ways
Center of Marker is marked clearly (See Plumb Bob Pictures & 5 Line Laser Pics)
Easy to make measurements with tape measure by lining up end of tape measure or distance needed with bottom of V cut
45 Degree Angle on all 4 sides for visibility of laser line when adjusting centerline (Especially when adjusting centerline under the vehicle.)
Can be used with Reflective Board
Made in USA
SGADAS- STD - These are standard marking squares that you will use with most vehicles you calibrate.
SGADAS-30 - Unique to Subaru Calibrations when using the Target Board that requires a 30mm Offset (Example - Autel Target Board - CSC0601/14)
SGADAS-39 - Unique to Hyundai & KIA Calibrations - Place in front of vehicle with plumb bob and have your 39mm from front target stand measurement automatically set.
ADVANTAGES of using these:
No more dirty floor issues that the tape won’t stick too
No more chalk lines to mark and remove
No more having to buy tape
best of all we have to say these markers have saved us a lot of setup time per job!
They literally pay for themselves in very little time and are an inexpensive investment at $129.99 for these 11pcs.
